The Honda - PACT program is cohort-based and requires department permission to enroll (Fall Start). Please contact program coordinator Justin Morgan at 937-512-3242 or justin.morgan8747@sinclair.edu for information.
This Sample Program Pathway is designed to provide an example of course selections in a term by term sequence. Please see an Academic Advisor for a plan specific to your academic needs.
Description: Work assignment practices that are necessary for beginning automotive service technicians. Hand tool usage, correcting wind noise and water leaks, oil changes, tire rotations and balancing, new vehicle prep, used car inspection. Eye protection and hand tools are required.
Description: Comprehension of Ohm’s law, basic electrical circuits, digital meter usage, batteries, starting and charging system operation. Diagnosis of wire harness repair procedures and service. One classroom, six lab hours per week.
Description: Steering system diagnosis and service including front and rear suspension components, wheel and tire and front and rear wheel alignment. Basic hand tools are required. One classroom, six lab hours per week.
Description: Students work in the field at an approved automotive service business. The credit that is earned for the internship is applied toward degree requirements. Students prepare and submit reports online and are evaluated by the course instructor as well as their on-site supervisor.
Prerequisites: Approval of Department
Description: Use ratio and proportion to solve applications in technology; convert within and between metric and customary systems of measurement; read and interpret measurement tools and gauges; simplify algebraic expressions; solve linear equations; apply the geometry of lines, angles, and circles to technology applications. Traditional testing (proctored or in Testing Center) is used in all online sections.
Prerequisites: MAT 0050 or Other (Satisfactory score on math placement test)
Term hours subtotal:
13
Description: Engine operation, nomenclature, measurements and tolerances, including service and overhaul procedures. Cooling, lubrication and valve train systems are discussed. Basic engine machining practices are covered. Basic hand tools are required for the course.
Description: Theory and operation of hydraulic braking systems, drum brake, disc brake and power assist diagnosis and service. One classroom, six lab hours per week.
Description: Students work in the field at an approved automotive service business. The credit that is earned for the internship is applied toward degree requirements. Students prepare and submit reports online and are evaluated by the course instructor as well as their on-site supervisor. Students will practice service procedures on steering and suspension, electrical systems and engines following their second semester. Twenty co-op hours per week.
Prerequisites: Approval of Department
Description: American political system at the national level, including process of government; democratic theory and development of the U. S. Constitution; citizen participation through voting; interest groups and political parties; structure, functions and powers of legislative, executive and judicial branches; issues of civil liberties and equal rights.
Description: This course is a broad introduction to welding with in-depth hands-on labs to include SMAW, GMAW, OAW, GTAW, and Resistance, commonly known as MIG, TIG, Ox-acetylene, and Stick (ARC) welding along with other types of metal joining options and instruction to include sheet metal layout, shearing, bending, riveting, brazing and spot welding. Welding safety, personal protection equipment, special welding tools will be taught in-depth and used by the students within the lab setting. The student will apply critical thinking and problem-solving skills to achieve the end results required using blue prints, verbal instructions or a combination of both. Two classroom, two lab hours per week.
Term hours subtotal:
15
Description: Operation and service of fuel injection systems. Testing and evaluation of emission controls, on-board diagnostic systems and engine condition. Basic hand tools required. Two classroom, six lab hours per week.
Prerequisites: AUT 1114
Description: Theory and operation of clutch, manual transmission and transaxle, rear axle, limited slip differential, drive shaft, universal joint, four- wheel drive/all-wheel drive, diagnosis and repair. Basic hand tools required. One classroom, six lab hours per week.
Term hours subtotal:
7
Description: Advanced electrical/electronic system diagnosis and troubleshooting of starting and charging systems, lighting systems, dashboard instrumentation, body control and accessory circuits. SRS system operation, testing and diagnosis. AC and DC motor theory, operation and diagnosis. Schematic utilization. Diagnose serial data bus communication and module systems. Two classroom, six lab hours per week.
Prerequisites: AUT 1114
Description: Theory and operation of automotive transmissions and transaxle systems. Lab experience in the overhaul and service of automatic transmissions and transaxles including mechanical, hydraulic and electronic systems diagnostics and testing.
Description: Students work in the field at an approved automotive service business. The credit that is earned for the internship is applied toward degree requirements. Students prepare and submit reports online and are evaluated by the course instructor as well as their on-site supervisor. Students will practice service procedures on engine performance, manual transmissions and axles following their third semester. Twenty co-op hours per week.
Prerequisites: Approval of Department
Description: Exploration of the development, maintenance and termination of interpersonal relationships. The focus is on effective verbal and nonverbal interactions between two people, highlighting methods of initiating and maintaining effective communication with, and understanding of, others through learning and applying interpersonal communication theory.
Description: This course examines the role of technology in the modern society. It explores the opportunities and dangers faced by humankind in the evolution of new technologies. It inquires into such questions as whether the human quest for mastery of nature has made us masters or slaves of the machine.
Term hours subtotal:
16
Description: Theory and operation of automotive heating and air-conditioning systems. Includes lab activity in diagnosis, service and repair procedures. Basic hand tools required. One classroom, six lab hours per week.
Description: Advanced diagnosis and repair of computer controlled fuel delivery, fuel injection, ignition, emission systems and proper use of advanced engine performance diagnostic equipment. Basic handtools required.
Prerequisites: AUT 1115
Description: Hybrid vehicle safety, theory and operation of automotive hybrid high voltage systems, batteries, charging systems, drivetrain components and emission systems. One classroom, three lab hours per week.
Prerequisites: AUT 2214
Description: Students work in the field at an approved automotive service business. The credit that is earned for the internship is applied toward degree requirements. Students prepare and submit reports online and are evaluated by the course instructor as well as their on-site supervisor. Students will practice service procedures on automatic transmissions and air-conditioning systems following their fourth semester. Twenty co-op hours per week.
Prerequisites: Approval of Department
Description: In English Composition I students learn reflective, analytical and argumentative writing strategies, incorporating sources and personal experience. Students will negotiate between public and private rhetorical situations and purposes to achieve academic literacy. They will write multiple drafts using a recursive writing process as they work toward fluency in style and mechanics. Note: Students who have not successfully completed the pre-requisites listed can register for ENG 1101 together with the co-requisite course ENG 0101 - English Composition I Booster.
Prerequisites: DEV 0035 or Other (Placement Test Score)
Term hours subtotal:
14